Checkout

You have no items in your shopping cart.

Pole & Rod Support

Pole and Rod Suppport

Items 1 to 10 of 13 total

per page
Grid  List 
Page:
  1. 1
  2. 2
  • Feeder arm

    Octbox Support - Feeder Arm MK19 A06B1

    Octbox Support - Feeder Arm MK19 Fitted with two M8 sockets to allow feeder heads to be fitted on the end or at 90 degrees to the feeder arm The Octbox adjustable feeder can extend from 65cm up to a length of cm and can be setup in seconds at any angle. The feeder arm is supplied with either a 25mm or 36mm dia connector that is secured to the seatbox leg. The feeder arm is slid on to a 25mm alloy post and secured by the same clamp system that is used to fix the Octbox legs. Supplied with Extendable feeder arm Available for any D25 or D36 Systems Learn More
    Excl. Tax: £29.17 Incl. Tax: £35.00

  • Octbox  Pole Roller FloorD

    Octbox Pole Roller FloorD

    The Octbox roller has been designed to the only pole roller you will ever need. The main picture shows three different setups that allow the roller to be used either with or without legs to achieve any height from 16cm (6.5inches) to 120cm (4ft) in a rock solid manner. Extendable spikes have been fitted into each support leg for additional rigidity which combined with the legs that can be set at any angle allows this roller to cover options not possible with any other roller. The Roller has two outer rollers that can be set at any angle and a middle roller that can be raised to create a double roller for those days when you need to break down the pole twice. The horizontal roller is ribbed to keep the pole in line when you ship back and is also made up of two separate rollers to support the double roller setup when needed. Tips On steep slopes fit the rear support legs on to the rear spikes to set them in a horizontal position while setting the fron support legs at a near vertical position. When you have achieved the perfect position and height extend the extendable spikes into the bank to fix the roller firmly in place. Best way to set up on more level ground is to extend all four support legs to the length you require. Fit them loosely to the pole roller frame in the position you want. The legs should be splayed out along the ground at this point. Start to lift the roller, as you do so the legs provided they are loose enough should start dropping to the level of the ground below them. Once the roller is at the height you need lock off the support legs by tightening the fixing clamp bolts. Finally if you are on soft ground go round each support leg and extend its spike into the ground. Luggage - We have developed bespoke luggage for this roller . If you wish to store a single roller we recommend our standard holdall. The XL holdall has been designed for two pole rollers Learn More
    Excl. Tax: £91.67 Incl. Tax: £110.00

  • Bump Bar with Pivoting Arm Set (Bump Bar ) Floor L

    Bump Bar with Pivoting Arm Set (Bump Bar ) Floor L

    Bump with Pivoting Arms (Bump Bar) & extending Posts Learn More
    Excl. Tax: £54.17 Incl. Tax: £65.00 As low as: £25.00

  • Topkit and Rod Roost Set MK20 . Floor M

    Topkit and Rod Roost Set MK20 . Floor M

    MK20 Rod and Topkit Roost Light weight but ultra strong roost that can be set at numerous angles with the ability to hold both rods and top kits up to top 6 without any risk of it slipping. No requirement for an additional support , the all alloy construction has a disc pin locking system that ensures no matter how much you load on to the roost and what ever angle it cannot slip. Removable red inserts are added to the rear sockets designated for top kits to ensure they cannot blow off the roost in windy conditions. The Topkit set design ensures that rods and top kits can be set from horizontal to almost vertical without any risk of top kits sliding backwards.. The rear and front topkit posts are square and fit into square adaptors to ensure they always remain parallel and square to each other This system can be supplied with either a 25mm or 36mm leg adaptor allowing it to fit on the majority of systems.

    Learn More
    Excl. Tax: £80.83 Incl. Tax: £97.00

  • Swivelling Tool Bar D25mm Adaptors & Post A10C3

    Swivelling Tool Bar D25mm Adaptors & Post A10C3

    D25 Light Alloy Tool Bar supplied with Extending Post with threaded insert. Will fit any Seat Box with 25mm round legs or posts. Length 56cm from centre to centre All alloy design is ultra light and incredibly strong and stable. Recommended Use - use as a swivelling adaptor bar to support feeder heads or pole support rollers. Use in conjunction with Mk18 feeder arm to fit two keepnets on to the left or right footplate leg of any 25mm round legs seat box Learn More
    Excl. Tax: £20.83 Incl. Tax: £25.00

  • Topkit Roost MK20 Adaptor

    Topkit Roost MK20 Adaptor

    MK20 Topkit Set adaptor Upgrades the Mk19 Topkit set to the MK20 Learn More
    Excl. Tax: £16.67 Incl. Tax: £20.00

  • Octbox Support - Roost Insert Set of 3    A02B2

    Octbox Support - Roost Insert Set of 3 A02B2

    Octbox Support - Roost Insert Set of 3 Learn More
    Excl. Tax: £2.92 Incl. Tax: £3.50

  • Fishing Bump Bar

    Octbox Support - XL Bump Bar inc Posts FloorK

    Octbox Support - XL Bump Bar inc Posts Learn More
    Excl. Tax: £41.67 Incl. Tax: £50.00

  • Octbox Support - XL Bump Bar (Less Posts) Floor L

    Octbox Support - XL Bump Bar (Less Posts) Floor L

    Octbox Support - XL Bump Bar (Less Posts) Learn More
    Excl. Tax: £20.83 Incl. Tax: £25.00

  • Extendable Fishing Adaptor Bar

    Octbox Extendable Extension Arm 25mm A03A3

    Octbox Extendable Extension Arm 25mm  


    The All Alloy Extendable Extension arm extends from 40cm to 70cm with round 25mm clamps on each end to fit on to any round 25mm leg system

    Learn More
    Excl. Tax: £20.00 Incl. Tax: £24.00

Items 1 to 10 of 13 total

per page
Grid  List 
Page:
  1. 1
  2. 2
Back to Top